油氣回收設備:加油站項目竣工環保驗收,應注意哪些內容?
已經辦理環評手續的加油站,項目竣工環保驗收時需要注意哪些內容呢?小編已整理相關資料,以供參考~
What should be noted during the environmental protection acceptance of gas stations that have already completed environmental impact assessment procedures? The editor has compiled relevant materials for reference~
01驗收重點
01 Key acceptance points
一次油氣回收 是通過壓力平衡原理,將油罐車在卸油過程中揮發的油氣重新收集到油罐車內,并運回油庫,進行油氣回收處理。
A single oil and gas recovery is achieved through the principle of pressure balance, which collects the evaporated oil and gas from the oil tank truck during the unloading process and transports it back to the oil depot for oil and gas recovery treatment.
二次油氣回收 是通過加油槍真空輔助式設備,將加油過程中揮發的油氣通過油氣回收管線收集到地下儲油罐
Secondary oil and gas recovery is achieved through a vacuum assisted device with a refueling gun, which collects the evaporated oil and gas during the refueling process through an oil and gas recovery pipeline and sends it to an underground storage tank
三次油氣回收 是將加油站地下儲油罐內由于壓力過大而排放的油氣,通過冷凝、膜分離等方法,進行回收處理。
Triple oil and gas recovery is the process of recovering and treating the oil and gas discharged from underground storage tanks at gas stations due to excessive pressure through methods such as condensation and membrane separation.
油氣回收裝置安裝情況《中華人民共和國大氣污染防治法》第四十七條明確規定,加油站應當按照國家有關規定安裝油氣回收裝置并保持正常使用。那什么是油氣回收裝置呢?油氣回收裝置包括卸油油氣回收系統(一次油氣回收)、加油油氣回收系統(二次油氣回收)以及三次油氣回收裝置(三次油氣回收)。油氣回收系統油氣回收在線監測設備根據《上海市生態環境局、市經濟和信息化委、市交通委關于進一步加強本市油氣回收治理工作的通知》(滬環氣〔2019〕234號),年銷售汽油量≥2000噸的加油站應安裝油氣回收在線監控設備,與生態環境部門聯網(上海市內加油站均應與上海市生態環境局聯網)。
According to Article 47 of the Air Pollution Prevention and Control Law of the People's Republic of China, gas stations shall install oil and gas recovery devices in accordance with relevant national regulations and maintain normal use. What is an oil and gas recovery device? The oil and gas recovery device includes an unloading oil and gas recovery system (primary oil and gas recovery), a refueling oil and gas recovery system (secondary oil and gas recovery), and a tertiary oil and gas recovery device (tertiary oil and gas recovery). According to the "Notice on Further Strengthening the Management of Oil and Gas Recovery in Shanghai" (Hu Huan Qi [2019] No. 234) issued by the Shanghai Ecology and Environment Bureau, Municipal Economic and Information Commission, and Municipal Transportation Commission, oil and gas recovery online monitoring equipment should be installed at refueling stations with an annual sales volume of ≥ 2000 tons of gasoline, and connected to the ecological environment department (all gas stations in Shanghai should be connected to the Shanghai Ecology and Environment Bureau).
驗收監測關于工況驗收監測應當在確保主體工程調試工況穩定、環境保護設施運行正常的情況下進行,并如實記錄監測時的實際工況。建議在驗收監測期間保持正常的工況。若國家和地方有關污染物排放標準或者行業驗收技術規范對工況和生產負荷另有規定的,按其規定執行。關于驗收監測內容主要監測項目包括:油氣回收系統(液阻、密閉性、氣液比、密閉點位泄漏檢測值、處理裝置排放濃度、在線監測系統校準和數據比對)、廠界廢氣、廠區內廢氣、廠界噪聲,以及其他環評及審批部門要求的監測內容。加油站廢氣通常為油氣,一般采用非甲烷總烴作為油氣排放控制項目。關于監測頻次油氣回收系統監測項目:
Acceptance monitoring of working conditions should be carried out under the condition of ensuring stable commissioning conditions of the main project and normal operation of environmental protection facilities, and the actual working conditions during monitoring should be truthfully recorded. It is recommended to maintain normal operating conditions during the acceptance monitoring period. If the national and local pollutant emission standards or industry acceptance technical specifications have other provisions on working conditions and production loads, they shall be implemented in accordance with their provisions. The main monitoring items for acceptance monitoring include: oil and gas recovery system (liquid resistance, airtightness, gas-liquid ratio, leakage detection values at sealed points, treatment device emission concentration, online monitoring system calibration and data comparison), factory boundary exhaust gas, factory internal exhaust gas, factory boundary noise, and other monitoring contents required by environmental impact assessment and approval departments. Gas station exhaust gas is usually oil and gas, and non methane total hydrocarbons are generally used as oil and gas emission control projects. Regarding the monitoring frequency of oil and gas recovery system monitoring projects:
廢氣:一般不少于2天、每天采不少于3個平行樣廢水:一般不少于2天,每天不少于4次廠界噪聲:一般不少于2天,每天晝夜各不少于1次(如果夜間無作業無工況,無需開展監測)。02驗收注意事項
Waste gas: generally not less than 2 days, no less than 3 parallel samples per day. Wastewater: generally not less than 2 days, no less than 4 times per day. Factory boundary noise: generally not less than 2 days, no less than 1 time per day and night (if there is no operation or working condition at night, no monitoring is required). 02 Acceptance precautions
驗收流程
Acceptance Process
1
one
2這些節點需要注意:1若項目涉及變動,判斷是否屬于重大變動,具體判定見取得環評審批意見后,項目變動了,我該怎么辦?2應在調試期前取得排污許可證或排污登記回執。3進入調試期后,方能開展驗收監測。
2. These nodes need to be noted: 1. If the project involves changes, determine whether it is a significant change. The specific determination can be found after obtaining the environmental impact assessment approval opinion. What should I do if the project changes? 2. The pollutant discharge permit or pollutant discharge registration receipt should be obtained before the commissioning period. Only after entering the debugging period can acceptance monitoring be carried out.
4根據《企業事業單位突發環境事件應急預案?jìng)浒腹芾磙k法(試行)》第十七條“建設單位制定的環境應急預案或者修訂的企業環境應急預案,應當在建設項目投入生產或者使用前,按照本辦法第十五條的要求,向建設項目所在地受理部門備案。”根據《上海市實施<企業事業單位突發環境事件應急預案?jìng)浒腹芾磙k法(試行)>的若干規定》第十八條”建設單位應在建設項目竣工驗收前完成備案工作?!?驗收?qǐng)?bào)告編制完成后,需在5個工作日內在“上海企事業單位環境信息公開平臺”公示不少于20個工作日。平臺網址:https://e2.sthj.sh.gov.cn:8081/jsp/view/hjxxgk/jsxmhp_index.jsp上海市平臺公示滿20個工作日后,需在5個工作日內在“全國建設項目竣工環境保護驗收信息系統”公示。系統網址:http://114.251.10.205/#/pub-message
According to Article 17 of the "Measures for the Administration of Filing of Emergency Plans for Sudden Environmental Incidents in Enterprises and Institutions (Trial)", "The environmental emergency plan formulated or revised by the construction unit shall be filed with the local acceptance department of the construction project in accordance with the requirements of Article 15 of these Measures before the construction project is put into production or use." According to Article 18 of the "Measures for the Administration of Filing of Emergency Plans for Sudden Environmental Incidents in Enterprises and Institutions (Trial) in Shanghai", "the construction unit shall complete the filing work before the completion and acceptance of the construction project. ”After the completion of the 5 acceptance reports, they must be publicly displayed on the "Shanghai Enterprise and Institution Environmental Information Disclosure Platform" for no less than 20 working days within 5 working days. Platform URL: https://e2.sthj.sh.gov.cn:8081/jsp/view/hjxxgk/jsxmhp_index.jsp After 20 working days of public announcement on the Shanghai platform, it is required to make a public announcement on the "National Construction Project Completion Environmental Protection Acceptance Information System" within 5 working days. System URL: http://114.251.10.205/#/pub -message
驗收期限
Acceptance deadline
驗收期限是指自建設項目環境保護設施竣工之日起至建設單位向社會公開驗收?qǐng)?bào)告之日止的時間。除需要取得排污許可證的水和大氣污染防治設施外,其他環境保護設施的驗收期限一般不超過3個月;需要對該類環境保護設施進行調試或者整改的,驗收期限可以適當延期,但最長不超過 12 個月。
The acceptance period refers to the time from the completion of the environmental protection facilities of the construction project to the date when the construction unit publicly releases the acceptance report to the society. Except for water and air pollution prevention and control facilities that require a pollutant discharge permit, the acceptance period for other environmental protection facilities generally does not exceed 3 months; If it is necessary to debug or rectify such environmental protection facilities, the acceptance period can be appropriately extended, but not exceeding 12 months.
本文由 油氣回收設備 友情奉獻.更多有關的知識請點擊 http://m.wmjdwx.com/ 真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.
This article is a friendly contribution from oil and gas recovery equipment For more related knowledge, please click http://m.wmjdwx.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.
地址:山東省菏澤市成武縣經濟開發區機電產業園鋼架結構單層5號
【微信二維碼】
留言咨詢Adopting different technology and process control schemes
魯公網安備 337172302372103號